, please spend more than £50Sur Ron Battery 60v 75Ah Endurance V3 Extreme Range 10kW
When Range is Everything!
The UK’s Biggest Range 60v Battery!!
Includes Charger
EBMX, VTB, Torp & KO Controllers Compatible
Full Function Bluetooth BMS
Lightweight Powerful and only 15.5 KG!
Fully Protected by ANT BMS
Stainless Steel 316 Powder Coated Casing
UK Warranty & Support
Shipping: UK (Free) Additional Shipping for Highlands and Islands +£30
EU land ship available, bank transfer only (20% VAT Removed)
For EU please email: [email protected]
Cash on collection available by appointment
Power: Medium (10kW)
Range: Very High (4500kWh)
Height: Medium (353mm)
Sur Ron Battery 60v 75Ah Endurance V3 Extreme Range 10kW is desgned for those that want to ride all day long with confidence this battery massivly increases range. Adding an after market controller set to 165A, power then jumps to 10Kw (far higher than a “bypassed” battery) and makes the big sing in comparison to standard.
Sur Ron Battery 60v 75Ah Endurance V3 Extreme Range 10kW is designed to run on a standard Sur Ron bike as a direct swap in battery, increasing the range by a monster 300%.
You can use your standard Sur Ron controller (no real power increase – just range) or you swap out your controller for an aftermarket controller and set it to 165A DC and phase maximum at 440A.
Power
This battery will work perfectly with the original Sur Ron standard Controller to give you range which is approximately 300% more than the OEM battery. If you want more power you will need a bigger controller we recomned our Atom (by Electron Cycles)
If this battery is to be used with an aftermarket controller, the maximum setting is 165A. DC Phase 450PhA and 10,000W:https://electroncycles.com/product/sur-ron-atom-controller-60v-72v-12kw-14-5kw-200a/
Exoskeleton /Casing
We have upgraded the casing to marine grade 316 stainless steel, so absolutely no rust issues here! Super tough and powder coated inside and out.
Connectors
The main battery to controller connectors we use are the same type as used by Sur Ron to keep everything compatible. This allows you to swap your standard battery back should you wish. If you have a 2024 Sur Ron with the newer round connector, you may have to retro fit the original Sur Ron battery loom (this is easy and cheap to do).
2024 Sur Ron Bikes
Sur Ron in their wisdom have changed the battery connector (oval in ornage sheath) for the 2024 model. It does not take as much power and is very difficult to obtain. These connectors are not compatible with our batteries (or anyone else’s battery). The simple work around is to install a pre 2024 loom or the free included high power loom. This takes about 30 minutes and is simple to do. If you then want to run your OEM 2024 battery, you will need to purchase an adapter. Most people sell their OEM battery to offset the cost of this much longer range and more powerful battery upgrade.
Some versions of the Sur Ron standard controller may go into limp mode if using this battery with no communication port (not using an aftermarket controller). This will need a very simple modification to the plug that normally connects to the battery. Please see the photo of the battery communication connector we supply. This is effectively two pins that are crossed with a simple piece of wire with a spade connector. Note the area circled in red in the photo.
Voltmeter
This Sur Ron Battery does not have an integrated voltmeter. We supply a voltmeter that nestles in your battery lid.
Domestic Electrics
All your bike accessories are still powered. Some believe that not using the circuit breaker direct to the controller removes the safety of the circuit breaker. However, all our batteries have a full working BMS. Any power shorts or irregular current and the BMS shuts down. This is much more sensitive and accurate than a mechanical breaker (you may note that the Sur Ron Ultra Bee does not use a circuit breaker and relies on the BMS alone).
Please note that on L1e Bikes an orange warning light may flicker on the main display and a small error code may appear. There is no fix for this and a consequence of using an aftermarket battery. Use the voltmeter we supply with your battery to keep track of the batteries state of charge – empty at 48V.
Specifications
Fitting
Connecting To Bike
When connecting the battery to the bike and to avoid a spark, turn the red trip switch on the bike to off. Connect the older original power cable and then turn the red trip to on. Then connect the new power leads. Removing the battery has no special order.
Battery Charging
First time charging is VERY important. Always connect the charger to the battery with the charger powered up at the mains first. This will stop a “Connection Spark”. The battery needs a “Balance Charge” on first charge. Please charge for 12 hours first time. Always charge your battery in a safe place and never unsupervised.
Bike Not Included
Warranty
For our Warranty terms, please check here: https://electroncycles.com/warranty-policy/
Disclaimer is available here: https://electroncycles.com/terms-and-conditions/
